Tapar Holes Wall
The appearance of cracks and holes in the walls is more common than we might think. These damages occur after a plumbing or electrical work, but also with the passage of time some deterioration can occur due to small accidental knocks.
Placing decorative elements and works of art on the walls is a good way to change the look of a space. However, we often dismiss the idea for fear of damaging the walls in the process. This is why it is worth learning how to fill holes in the wall, in order to make all the necessary modifications without being invaded by doubts.
The best product to cover holes in the walls
Covering holes and other defects can make a big difference when it comes to repairing walls, which is why it is a very common practice in homes. A few years ago, plaster or plaster was used to cover holes, especially in ceilings made of this material. In that case, the plaster powder had to be mixed with water to create a consistent mass and thus patch up the problem areas.
Currently, there are many products that serve this purpose, some are ready to be used and others are very easy to prepare, but it is important to know that each one has been manufactured for specific uses, according to its composition and properties. of the material , therefore, you have to check the characteristics well before making the purchase.
In this sense, we can say that the putty to cover holes is the most practical solution to use in walls, since most of the cracks and holes that appear in houses are small and this product comes in minimal quantities, is relatively cheap and it is ready to be used immediately.
The key to choosing a good putty is its ability to maintain volume after drying time. Generally, the putty tends to shrink, therefore, once it dries, you have to reapply another layer and repeat the process as many times as necessary to completely cover the hole. However, if we choose a putty that does not reduce its size, the process is faster and easier, since we only have to apply it once.
Step by step: Cover a hole in the wall
If you are wondering how to cover a large hole in the wall, you should know that you need to buy a pot of putty that has an adequate amount depending on the damage to the wall. In extreme cases, it is preferable to fill a hole in the wall with cement, for this we must prepare a mortar with sand and water, so that we only have to use the putty for the finish.
However, here is a series of steps on how to cover a hole in the wall without cement, in case it is a minor repair job. For this DIY project we need a putty knife , fine grit sandpaper and a high quality putty that doesn’t shrink.
- Check the actual size of the hole
Both cracks and holes in the walls can deceive us at first glance, since they sometimes seem small, but it is possible that a larger area has been affected. In this sense, it is best to check with the tip of the triangular spatula, to check the real magnitude of the damage to the wall .
Also, although it may seem hard to believe, a hole that is too small in the wall can be more complicated to cover, so it is advisable to open it a little, making circles with the tip of the metal spatula. If it is a crack, you can go all the way with the tool several times until you check that there is no deeper crack in the wall.
- clean the surface
Regardless of the type of putty you have, this product generally adheres best when the surface is completely clean, but using the putty knife can create excessive dust, so cleaning with a dry brush is necessary . This step can be speeded up if you use a vacuum cleaner, in addition, this guarantees a deeper cleaning for a better fixation of the putty on the wall.
- Apply the putty
This is the most important part when repairing a hole in the wall. The first thing we should mention at this point is that if you have putty powder, you have to use 500 ml of water per kilo and mix until you get a homogeneous mass. For this it is not necessary to use a concrete mixer (here you will find some purchase options), since you can do it with the same spatula. If, on the other hand, you have bought ready-to-use putty, it is good to stir it well before applying.
On the other hand, it is advisable to add the putty in small quantities, to avoid excess and protuberances. In the case of cracks, it is necessary to apply first perpendicularly and then along the fault, in order to fill in evenly.
- sand and paint
If when drying you notice that the putty has diminished, you just have to sand the surface a little, clean and apply a second layer . When completely dry, sand again to match. The best way to disguise this type of repair is to paint the entire wall, to avoid the difference between the new and old paint. However, in some cases it is enough to paint the repaired area.
As we can see, covering wall cracks can be quite simple if we use the right product, but for this it is important to take into account the type of surface to be repaired and the size of the hole.
